Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADIFLAM S RV100 FR 322 BK - PA6-GF10 - RadiciGroup High Performance Polymers

Check here, which other Radiflam S datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - 도표

Any use of this information falls under the rules of our disclaimer.

제품 설명서

PA6 flame retardant injection moulding grade, halogen and phosphorus free. Glass Fibre reinforced. Black colour.

Environmentally friendly flame retardant grade with low toxicity and minimum smoke density during combustion. Rated V-0 according to UL-94. Improved thermal conductivity.

Processing/Physical Characteristics	건조/응축	단위	시험규격
ISO 데이터
성형 수축률, 평행	0.4 / *	%	ISO 294-4, 2577
성형 수축률, 수직	0.7 / *	%	ISO 294-4, 2577

기계적 특성	건조/응축	단위	시험규격
ISO 데이터
인장탄성률	12700 / 7500	MPa	ISO 527
파단시 강도	120 / 85	MPa	ISO 527
파단시 신율	1.8 / 2.5	%	ISO 527
챠피 충격 강도 , +23°C	28 / 35	kJ/m²	ISO 179/1eU
챠피 충격 강도, -30°C	20 / -	kJ/m²	ISO 179/1eU
챠피 노치드 충격 강도, +23°C	4 / 5	kJ/m²	ISO 179/1eA
챠피 노치드 충격 강도, -30°C	3.5 / -	kJ/m²	ISO 179/1eA

열적 특성	건조/응축	단위	시험규격
ISO 데이터
녹는점, 10°C/min	220 / *	°C	ISO 11357-1/-3
하중하에서의 변형온도, 1.80 MPa	200 / *	°C	ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa	217 / *	°C	ISO 75-1/-2
비카트 연화 온도, B	212 / *	°C	ISO 306
1.5mm 평균두께에서의 난연성	V-0 / *	class	IEC 60695-11-10
테스트 두께	1.6 / *	mm	-
Yellow Card 유효한	예 / *	-	-
두께 H인 제품의 난연성	V-2 / *	class	IEC 60695-11-10
테스트 두께	0.8 / *	mm	-
Yellow Card 유효한	예 / *	-	-
산소지수로서의 난연성	58 / *	%	ISO 4589-1/-2

전기적 특성	건조/응축	단위	시험규격
ISO 데이터
부피 저항	1E13 / 1E11	Ohm*m	IEC 62631-3-1
표면 저항	* / 1E10	Ohm	IEC 62631-3-2
CTI	600 / -	-	IEC 60112

기타 특성	건조/응축	단위	시험규격
물에서의 흡수성	2.8 / *	%	ISO 62와 유사
조건에서의 흡습성	1.4 / *	%	ISO 62와 유사
밀도	1720 / -	kg/m³	ISO 1183

도표

특징

생산 공정

사출 성형

인도 유형

과립, 검정

부가물

이형제

특별 특성

난연성, Halogen-free, Phosphorus-free, 열안정성, Thermally Conductive

지역별 검색

쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧

기타 정보

사E성

The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.10%. Typical conditions with a desiccant drier: temperature 80 ° C, dew point -20 ° C or below, time 2-4 h or more. Avoid excessive shear rates and high thermal stresses for better processing. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters

Melt Temperature	Mold Temperature	Injection Speed
280 - 300°C	80 - 90°C	medium-high

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.